Cm-100-S2Lc20 Media Converter, Perle Systems, Mfr#: 05052240

Transceiver/Media Converter

100Base-TX, 100Base-LX

9/125 µm

Yes

1

12.43 Mile

Duplex

Internal

MCR1900 Media Converter Chassis

Yes

2

5.28 oz

CM-100-S2LC20 Fast Ethernet Media Converter

1

Enabled (Default)- The media converter uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to advertise full duplex; Disabled- The media converter sets the 100Base-TX port to full duplex.

0 C to 50 C (32 F to 122 F)

FCC Part 15 Class A, EN55022 Class A

Pause should be enabled when all devices connected to the media converter support pause. Auto-Negotiation must be Enabled to use this feature; Enabled (Default)- The Media converter will advertise Pause capability during Auto-Negotiation on the 100Base-TX interface; Disabled- The Media converter will advertise that it does not have Pause capability during Auto-Negotiation on the 100Base-TX interface.

This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received.

If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the 100Base-TX interface to set the port MDI or MDIX whichever is appropriate; Enabled (Default)- Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable; Disabled- If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media convertor's transmitter and the partner devices transmitter are connected to the others receiver. The Media Convertor's 100Base-TX port is configured as MDI with this switch setting.

6.8

32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power

RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable

Captive thumb screws enable fast insertion and removal. Can be further tighten with a screwdriver.

Enabled (Default)- When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter; When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on; Disabled- The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface.

EN55024

Up to 3,048 meters (10,000 feet)

Single mode dual LC Media Converters; Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron; Single Mode: 9/125 micron (ITU-T 625)

u003c10-12

This green LED is operational only when power is applied. The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received.

1.5kv

minimum range of -25 C to 70 C (-13 F to 158 F)

5% to 90% non-condensing

The media converter can perform a loopback on the 100Base-X fiber interface; Disabled (Default - Up); Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface.

5% to 95% non-condensing

Auto (default) enable management module to overwrite hardware switch settings; Switch - Use onboard DIP switches

This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.

2

EN 60825-1:2007

UL 60950-1

Canada

1